High speed response 1 ms

Mounting the detachable head close to the detecting section minimizes piping and enables response time of 1 ms, as well as greatly decreasing tact time delay.
In addition, the ultra-small and light-weight design of the head means it can easily be mounted on moving sections.

Independent use of sensor head possible

Data can be controlled by taking the analog voltage output (1 to 5 V) from the sensor head and feeding it to a digital panel meter.

Convenient intermediate cable with connector

Intermediate cable with connector for connecting the sensor head and the controller makes operation and maintenance easier.

Sensor head with operation indicator

The sensor head is also equipped with operation indicator. Output ON / OFF can be checked on the sensor head, so that it is suitable for checking operation at the suction head. (Linked to Comparative Output 1)

A total of 10 head variations

A total of 10 head variations to meet all production demands.

■Vacuum pressure type (0 to -101.3 kPa)
M5 male thread
R (PT) 1/8 male thread / M5 female thread
NPT 1/8 male thread / 10-32UNF female thread
10-32UNF male thread

■Positive pressure type (0 to 1.000 MPa)
M5 female thread
R (PT) 1/8 male thread / M5 female thread
NPT 1/8 male thread / 10-32UNF female thread

■Compound pressure type (-100.0 to 100.0 kPa)
M5 female thread
R (PT) 1/8 male thread / M5 female thread
NPT 1/8 male thread / 10-32UNF female thread

Globally usable

Two types of output, NPN and PNP, are available to allow use of the sensors anywhere in the world. The sensor, of course, conforms to the CE marking EMC Directive.
Further, it has obtained UL Recognition.

Easy mounting, mobile pressure port

The head's pressure port can be rotated independently (freeturning) of the sensor head. In addition to being easy to mount, the cable can be laid in any direction.

Light-weight, compact design

The controller was designed to be light-weight and compact.
Control panel setup is low cost and requires minimal space.

Supplied with a panel mounting bracket

A panel mounting bracket (MS-DP-1) is enclosed to enable simple mounting of the controller onto the panel surface, thus contributing to the total cost reduction. Since the panel thickness can be from 1 to 6 mm 0.039 to 0.236 in, the controller can even be mounted on thick, resinmade panels.
The attached panel mounting bracket enables vertical installation.

2 types of sensor mounting brackets are available

Using the vertical mounting bracket (MS-DP-3) and the horizontal mounting bracket (MS-DP-4), the devices can be installed in the space inside machines or boxes.

DIN rail mounting bracket is available

The controller can be mounted even on a 35 mm 1.378 in width DIN rail by using the optional DIN rail mounting bracket (MS-DP-2). It can be fitted even in a narrow space inside your equipment because it can be mounted from four directions.

Made for horizontal panel mounting

Using the horizontal multiple panel mounting bracket, the MS-DP-5 (optional), direct panel surface horizontal mounting is rendered possible. For installation, the panel thickness must be from 1 to 6 mm 0.039 to 0.236 in.

User friendly two-color digital display

The user friendly two-color digital display changes color when output changes (ON / OFF), making it easy to check operation status at a glance. The display color can be linked to Comparative Output 1 or Comparative Output 2.

Two independent outputs plus analog voltage output

In addition to two independent outputs (ON / OFF), analog voltage output (1 to 5 V) is also available. The different outputs allow you to create solutions for a wide variety of applications.

Two operation indicators

There are two operation indicators that light respectively when Comparative Output 1 or Comparative Output 2 is ON. They are convenient for intensive operation checks.

Sensor head auto-recognition

The head's auto-recognition function means you don't have to manually set the head type at the controller, saving you valuable time.

Equipped with external input function (auto-reference and remote zero-adjustment functions)

If the reference pressure of the equipment changes, the auto-reference function can compensate the threshold levels by the amount of change and the remote zeroadjustment function can reset the display value to zero via external input. These functions are ideal for places where the reference pressure fluctuates wildly, or where fine settings are desired.
The external input functions can be selected with the supplementary setting mode using key operations.

Example:
When leak test mode is applied, Comparative Output 1 detects the filling pressure and Comparative Output 2 detects the leakage.